Subscribe for 10% off your first order

Step-by-Step Guide

Please find the step-by-step guide below for how to set up your BrosTrend AX3000 Wi-Fi 6 device in different working modes. Just know that our help doesn't stop here. Contact us if you have any questions.

Contact us
Extender Mode

Extends your existing Wi-Fi coverage wirelessly.

Step 1: Power on

Plug the extender into a power outlet in the same room as your router. Wait until the LED indicator blinks red slowly.

Step 2: Connect the extender to Your Existing Wi-Fi Network

Method 1: Set Up Through the Web Management Page

1. Connect your mobile phone to the extender's default Wi-Fi network:
BrosTrend_EXT,or
BrosTrend_5GEXT
Make sure it is not connected to an Ethernet cable with Internet access.

2. The web management page should open automatically.

If it does not open, open a web browser and enter http://brostrendwifi.com or 192.168.0.254 in the address bar (NOT in the search box, and WITHOUT “https”).

3. The device will automatically detect and select Extender Mode / Wi-Fi to Ethernet Adapter Mode.

Note: If Wireless Access Point Mode is detected instead, disconnect the Ethernet cable from the extender. Then click Switch and select Extender Mode / Wi-Fi to Ethernet Adapter Mode manually.

4. Select the Wi-Fi network you want to extend, enter its password, and click Next.

5. The extender will verify the Wi-Fi password.

5.1. If the password is incorrect, follow the on-screen message and try again.

5.2. If the password is correct, set the extended Wi-Fi names and password, and create a login password for future access to the web management page. Then click Next.

6. Wait about 1 minute. Check the LED indicator to confirm that the extender has connected to your Wi-Fi network successfully.

Method 2: Set Up Through the WPS Button

* This method is only applicable when your router has a WPS button. Otherwise, use Method 1.

1. Plug the extender into a power outlet in the same room as your router. Wait until the LED indicator blinks red slowly.

2. Press the WPS button on your router.

3. Within 2 minutes, press and hold the extender's WPS/RESET button for 1–3 seconds.

4. The LED indicator will blink green rapidly.

5. When the LED indicator turns solid on, the extender has connected to your router successfully.

Default Extended Wi-Fi Network Information
• Wi-Fi Names (SSID):Your Wi-Fi Name_EXT and Your Wi-Fi Name_5GEXT
• Wi-Fi Password:The same as the password of your Wi-Fi network.

Note:
For better security, create a login password for the web management page as soon as possible after WPS setup. Otherwise, any device connected to the extender (wired or wirelessly) may be able to access the web management page.Connect a wireless device to the newly extended Wi-Fi network and enter http://brostrendwifi.com in your browser's address bar (NOT in the search box, and WITHOUT “https”) to access the web management page. You will then be redirected to the page for setting up the login password.

Step 3: Relocate

Plug the extender into a power outlet halfway between your Wi-Fi router and the Wi-Fi dead zone.
Setup Complete!

Tips for Optimal Signal Quality

• Install the extender within your router's Wi-Fi coverage.
• Place the extender in an open area and avoid obstacles that may block or weaken Wi-Fi signals, such as metal objects and large furniture.
• Keep the extender away from electrical appliances that may cause Wi-Fi interference, such as microwave ovens and induction cookers.

Wi-Fi to Ethernet Adapter Mode

Connects to your existing Wi-Fi network and provide internet access for a wired device through the Ethernet port of this adapter.

Step 1: Power on

Plug the adapter into a power outlet in the same room as your router. Wait until the LED indicator blinks red slowly.

Step 2: Connect the Adapter to Your Wi-Fi Network

Method 1: Set Up Through the Web Management Page

1. Connect your mobile phone to the adapter's default Wi-Fi network:
BrosTrend_EXT,or
BrosTrend_5GEXT
Make sure the adapter is not connected to an Ethernet cable with Internet access.

2. The web management page should open automatically.

If it does not open, open a web browser and enter http://brostrendwifi.com or 192.168.0.254 in the address bar (NOT in the search box, and WITHOUT “https”).

3. The device will automatically detect and select Extender Mode / Wi-Fi to Ethernet Adapter Mode.

Note: If Wireless Access Point Mode is detected instead, disconnect the Ethernet cable from the extender. Then click Switch and select Extender Mode / Wi-Fi to Ethernet Adapter Mode manually.

4. Select the Wi-Fi network you want to extend, enter its password, and click Next.

5. The adapter will verify the Wi-Fi password.

5.1. If the password is incorrect, follow the on-screen message and try again.

5.2. If the password is correct, set the extended Wi-Fi names and password, and create a login password for future access to the web management page. Then click Next.

6. Wait about 1 minute. Check the LED indicator to confirm that the adapter has connected to your Wi-Fi network successfully.

Method 2: Set Up Through the WPS Button

* This method is only applicable when your router has a WPS button. Otherwise, use Method 1.

1. Plug the adapter into a power outlet in the same room as your router. Wait until the LED indicator blinks red slowly.

2. Press the WPS button on your router.

3. Within 2 minutes, press and hold the adapter's WPS/RESET button for 1–3 seconds.

4. The LED indicator will blink green rapidly.

5. When the LED indicator turns solid on, the adapter has connected to your router successfully.

Default Extended Wi-Fi Network Information
• Wi-Fi Names (SSID):Your Wi-Fi Name_EXT and Your Wi-Fi Name_5GEXT
• Wi-Fi Password:The same as the password of your Wi-Fi network.

Note:
For better security, create a login password for the web management page as soon as possible after WPS setup. Otherwise, any device connected to the extender (wired or wirelessly) may be able to access the web management page.Connect a wireless device to the newly extended Wi-Fi network and enter http://brostrendwifi.com in your browser's address bar (NOT in the search box, and WITHOUT “https”) to access the web management page. You will then be redirected to the page for setting up the login password.

Step 3: Connect Your Wired Device

Connect your wired device, such as a smart TV, computer, game console, or printer, to the adapter's Gigabit Ethernet port using an Ethernet cable.
Setup Complete!

In this case, you need to configure the IP Address and DNS server address of your wired devices as AUTO OBTAIN.

Tips:
For a stable connection, install the adapter within your router's Wi-Fi coverage range. Keep the adapter away from electrical appliances that may cause Wi-Fi interference, such as microwave ovens and induction cookers.

Wireless Access Point Mode

Creates another Wi-Fi Network by connecting to the LAN port of your existing router or an active Ethernet port via an Ethernet cable.

Step 1: Power on

Plug the access point into a power outlet. Wait until the LED indicator blinks red slowly.

Step 2: Connect to the Internet

Use an Ethernet cable to connect the access point's Ethernet port to an active Ethernet port or a LAN port on your router.

Step 3: Create Your Wi-Fi Network

1. Connect your mobile phone to the access point's default Wi-Fi network:
BrosTrend_EXT, or
BrosTrend_5GEXT

2. The web management page should open automatically.

If it does not open, open a web browser and enter http://brostrendwifi.com in the address bar (NOT in the search box, and WITHOUT “https”).

3. The device will automatically detect and select Wireless Access Point Mode.

If Extender Mode / Wi-Fi to Ethernet Adapter Mode is detected instead, click Switch and select Wireless Access Point Mode manually. After setup, connect the access point's Ethernet port to an active Ethernet port or a LAN port on your router.

4. Set the Wi-Fi names (SSIDs), Wi-Fi password, and a login password for future access to the web management page. Then click Next.

Wait about 1 minute. When the LED indicator turns solid green, the access point is connected to the Internet successfully.
Setup Complete!

Mesh Networking Mode

Creates or expands your whole-home mesh Wi-Fi network. Compatible with BrosMesh or EasyMesh devices. Works as a primary or satellite mesh node.
• BrosMesh: BrosTrend's proprietary Mesh technology.
• EasyMesh: A universal Mesh standard supported by many brands.

By Button (recommended)

Before You Start

• This pairing method is only supported between BrosMesh or EasyMesh-compatible devices.
• At least two compatible devices are required to set up a mesh network, with one working as the primary node and the others as satellite nodes.
• To use this device as a Mesh primary node, configure it in Access Point Mode or Router Mode.
• To use this device as a Mesh secondary node, follow the setup instructions below.

Step 1: Reset the Device

Press and hold the WPS/RESET button on the side of this device for more than 10 seconds, then release it. The LED indicator will flash red rapidly, indicating that this device is restoring factory settings. (If you have confirmed that this device is already in factory default state, you may skip this step and proceed directly to next step.)

Step 2: Enable Mesh Pairing Mode

Power on this device near the primary node device. After this device has fully started up (with the LED indicator blinking red slowly), press and hold the WPS/RESET button on this device for 1–3 seconds, then release it. The LED indicator will flash green rapidly, indicating that mesh pairing has started.

Step 3: Add this Devcie to the Mesh Network

Within 2 minutes, press the MESH button on the primary node. When the LED indicator turns solid green, the mesh setup is complete and the Wi-Fi SSID and password will automatically synchronize with the primary node. Relocate it to a suitable location and enjoy the seamless whole-home mesh Wi-Fi network!

By Cable

Before You Start

• This pairing method is only supported between BrosMesh or EasyMesh-compatible devices.
• At least two compatible devices are required to set up a mesh network, with one working as the primary node and the others as satellite nodes.
• To use this device as a Mesh primary node, configure it in Access Point Mode or Router Mode.
• To use this device as a Mesh secondary node, follow the setup instructions below.

Step 1: Reset the Device

Press and hold the WPS/RESET button on the side of this device for more than 10 seconds, then release it. The LED indicator will flash red rapidly, indicating that this device is restoring factory settings. (If you have confirmed that this device is already in factory default state, you may skip this step and proceed directly to next step.)

Step 2: Add this Devcie to the Mesh Network

After this device has fully started up (with the LED indicator blinking red slowly), use an Ethernet cable to connect this device's Ethernet port to the LAN port of the primary node device. Alternatively, connect both this device and the primary node device to the LAN ports of the same switch or router. When this device's LED indicator turns solid green, the mesh setup is complete and the Wi-Fi SSID and password will automatically synchronize with the primary node. Relocate it to a suitable location and enjoy the seamless whole-home mesh Wi-Fi network!

Wi-Fi Router Mode (Not supported on US models)

Works as a standalone Wi-Fi router by connecting to the Ethernet port of your modem via an Ethernet cable.

Step 1: Power on

Plug the device into a power outlet. Wait until the LED indicator blinks red slowly.

Step 2: Connect to the Internet

Use an Ethernet cable to connect this device's Ethernet port to an active Ethernet port or a LAN port on your modem.

Step 3: Create Your Wi-Fi Network

1. Connect your mobile phone to this device's default Wi-Fi network:
BrosTrend_EXT, or
BrosTrend_5GEXT

2. The web management page should open automatically.

If it does not open, open a web browser and enter http://brostrendwifi.com in the address bar (NOT in the search box, and WITHOUT “https”).

3. After the device completes smart mode detection, click Switch, then select Wi-Fi Router Mode.

4. The device will automatically detect the Internet connection type, configure the Internet settings, and continue to Wi-Fi Settings.

If a Detection Error occurs, follow the on-screen recommendations and try again. 
Alternatively, you can click Skip to complete the remaining wireless settings first. After the setup is complete, connect the device to your modem using an Ethernet cable for internet access.

5. Set the Wi-Fi names (SSIDs), Wi-Fi password, and a login password for future access to the web management page. Then click Next.

6. Wait about 1 minute. When the LED indicator turns solid green, the device is connected to the Internet successfully.
Setup Complete!

WISP Mode (Not supported on US models)

Creates a new Wi-Fi network by wirelessly connecting to public Wi-Fi (from an ISP, hotel, airport etc.)

Before you begin: Please set up this device in another mode first, then switch to WISP mode.

1. Connect your phone to the device's Wi-Fi network.

2. Open a web browser and enter http://brostrendwifi.com in the address bar (NOT in the search box, and WITHOUT “https”) to access the web managemnet page.

3. Go to Working Mode, then select WISP Mode.

4. Select the Wi-Fi network you want to connect to, enter its password, and click Connect.

5. The device will begin the configuration process and restart. Your Wi-Fi names and passwords will remain the same as before switching modes.

6. Wait about 1 minute. Check the LED indicator to confirm that the device has connected to the upstream Wi-Fi network successfully.
Setup Complete!